Clik here to view.
Information on hardware type (physical or virtual)
I am trying to do a report and I am looking for the hardware info of the nodes but I am not able to find it in the Nodes table. Anyone knew where I could obtain this information? I am trying to...
View ArticleEvaluating SAM - total noob - how to view servers - just seeing All Nodes
Hello, please forgive total noob here and trying to figure out the software.My current goal is to have a listing of all servers , showing RAM, CPU , drive space and other possible info.We have...
View ArticlePop-up Nested Maps?
I've dabbled slightly with creating nested maps in Network Atlas, but I haven't found a way to make it ideal for my situation. At my work I monitor about 50 remote sites; each site has a single L3...
View ArticleClik here to view.
Email Web page action no longer works after NPM 11.5 upgrade
I enabled the High Receive Percent Utilization with Top Talkers alert some time ago. It emailed a web page listing the top talkers. It worked fine for years. After upgrading to NPM 11.5, this alert...
View ArticleWorldmap not getting updated with new devices in groups.
Hi guys, I need a bit of help here.... In my world map I got all my devices, but when a new devices is added into a one of my groups, my world map dont get updated. Mean like this. In my All groups...
View ArticleClik here to view.
Monitoring Fortinet cluster - strange and inaccurate utilization numbers
Hi all - For the last couple of weeks, I've been getting very strange utilization numbers on our Fortinet boxes. We run a HA cluster with two Fortigate 600Cs.We've made no changes of which I'm aware on...
View ArticleCisco Hardware monitoring
Without digging into MIB's, is there a way to monitor the hardware of Cisco switches for failed or predicted failure of hardware such as ports? Is this something that is being researched?
View ArticleWebsite Error - Orion WebConsole Admin Settings Page
Hi, I recently upgraded to NPM 11.5.0 & SAM 6.2.0.When I login as Admin to the Orion WebConsole using the default credentials, am able to get to the Dashboard.But when I try to access Settings (top...
View ArticleClik here to view.
How to enable Hardware Health Monitoring in NPM
I just installed NPM 10.4.2. How do I enabled the Hardware Health Monitoring? I checked the NPM Admin Guide and it didn't say what are the requirements or process on how to enable this feature. Thank...
View ArticleClik here to view.
Remove Sylog and Traps tabs
Hi,i installed NPM product and it working well but Remove Syslog and Traps tabs and i don't khnow why so I hope someone could explain it to me. Please help.Thanks,
View Articlehi
hi allany one could you please help me on configure vbscript globally for all solar winds monitors.
View ArticleNCM Triggers SNMP Protocol Violation on Cisco IPS
I have a lrge number of alerts from my Cisco IPS (runing signature 867.0). They are all showing my NCM/NPM server as the attacker. The message is high 4507-6 SNMP Protocol Violation (<IPS HOST...
View ArticleWindows Mount Points via SNMP – How to.
If like me you are somewhat startled by the fact you cannot monitor mount point in the same way as a normal logical disk, read on. It is possible without using an expensive APM license, by using a...
View ArticleClik here to view.
Adding Live Weather to the "Worldwide Map" Resource
Adding Live Weather to the "Worldwide Map" Resource Summary: This will allow you to add live weather to the worldwide map based on the OpenWeatherMap project (free).Limitations: The map must be on a...
View Articleapc basic output status alert
trying to find how I can use the custom poller to setup a alert when the unit is on battery when setting up my alert this is how I have but I cannot figure how to setup for it to recognize it ....
View ArticleClik here to view.
Information on hardware type (physical or virtual)
I am trying to do a report and I am looking for the hardware info of the nodes but I am not able to find it in the Nodes table. Anyone knew where I could obtain this information? I am trying to...
View ArticleAll Alerts widget no longer honoring Account Limitations after upgrade to NPM...
I recently upgraded to NPM v11.5.2 and I have found that my clients that have account limitations making it so they can only see nodes associated with their account can see all alerts for every system....
View ArticleNPM 11.5.2 RC1 is in the customer portal
HiIs that SR for 11.5 ?if YES why is it RC1? /SJA
View ArticleClik here to view.
On the Manage Pollers screen, why is Edit grayed out?
I'm hoping I'm just being dumb here and missing something obvious, but when I go to the Manage Pollers page and select a poller, the Edit option is grayed out. This is the case no matter which poller I...
View Article